Al guna sugerencia por favor. No arrancan los motores,cuando conecto reconoce la bateria pero luego nada.En el Gui se ve que el mando de motor actúa.Lo tengo programado así.
*
MultiWiiCopter by Alexandre Dubus
radio-commande.com
February 2011 V1.pre7
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
any later version. see <
http://www.gnu.org/licenses/>
*/
/*******************************/
/****CONFIGURABLE PARAMETERS****/
/*******************************/
/* Set the minimum throttle command sent to the ESC (Electronic Speed Controller) */
/* This is the minimum value that allow motors to run at a idle speed */
#define MINTHROTTLE 1300 // for Turnigy Plush ESCs 10A
//#define MINTHROTTLE 1120 // for Super Simple ESCs 10A
//#define MINTHROTTLE 1190
/* The type of multicopter */
//#define GIMBAL
//#define BI //experimental
//#define TRI
//#define QUADP
//#define QUADX
//#define Y6
#define HEX6
//#define FLYING_WING //experimental
#define YAW_DIRECTION 1 // if you want to reverse the yaw correction direction
//#define YAW_DIRECTION -1
#define I2C_SPEED 100000L //100kHz normal mode, this value must be used for a genuine WMP
//#define I2C_SPEED 400000L //400kHz fast mode, it works only with some WMP clones
//#define PROMINI //Arduino type
#define MEGA
//enable internal I2C pull ups
#define INTERNAL_I2C_PULLUPS
//****** advanced users settings *************
/* The following lines apply only for a pitch/roll tilt stabilization system */
/* It is not compatible with Y6 or HEX6 */
/* Uncomment the first line to activate it */
//#define SERVO_TILT
#define TILT_PITCH_MIN 1020 //servo travel min, don't set it below 1020
#define TILT_PITCH_MAX 2000 //servo travel max, max value=2000
#define TILT_PITCH_MIDDLE 1500 //servo neutral value
#define TILT_PITCH_PROP 10 //servo proportional (tied to angle) ; can be negative to invert movement
#define TILT_ROLL_MIN 1020
#define TILT_ROLL_MAX 2000
#define TILT_ROLL_MIDDLE 1500
#define TILT_ROLL_PROP 10
/* I2C gyroscope */
//#define ITG3200
/* I2C accelerometer */
//#define ADXL345
#define BMA020
//#define BMA180
/* I2C barometer */
//#define BMP085
/* I2C magnetometer */
//#define HMC5843
/* ADC accelerometer */ // for 5DOF from sparkfun, uses analog PIN A1/A2/A3
//#define ADCACC
/* The following lines apply only for specific receiver with only one PPM sum signal, on digital PIN 2 */
/* IF YOUR RECEIVER IS NOT CONCERNED, DON'T UNCOMMENT ANYTHING. Note this is mandatory for a Y6 setup */
/* Select the right line depending on your radio brand. Feel free to modify the order in your PPM order is different */
//#define SERIAL_SUM_PPM PITCH,YAW,THROTTLE,ROLL,AUX1,AUX2,CAMPITCH,CAMROLL //For Graupner/Spektrum
//#define SERIAL_SUM_PPM ROLL,PITCH,THROTTLE,YAW,AUX1,AUX2,CAMPITCH,CAMROLL //For Robe/Hitec/Futaba
//#define SERIAL_SUM_PPM PITCH,ROLL,THROTTLE,YAW,AUX1,AUX2,CAMPITCH,CAMROLL //For some Hitec/Sanwa/Others
/* interleaving delay in micro seconds between 2 readings WMP/NK in a WMP+NK config */
/* if the ACC calibration time is very long (20 or 30s), try to increase this delay up to 4000 */
/* it is relevent only for a conf with NK */
#define INTERLEAVING_DELAY 3000
//for V BAT monitoring
//after the resistor divisor we should get [0V;5V]->[0;1023] on analog V_BATPIN
// with R1=33k and R2=51k
#define VBATLEVEL1_3S 960
#define VBATLEVEL2_3S 880
#define VBATLEVEL3_3S 800
/* when there is an error on I2C bus, we neutralize the values during a short time. expressed in microseconds */
/* it is relevent only for a conf with at least a WMP */
#define NEUTRALIZE_DELAY 100000
/* this is the value for the ESCs when thay are not armed */
/* in some case, this value must be lowered down to 900 for some specific ESCs */
#define MINCOMMAND 1000
/* this is the maximum value for the ESCs at full power */
/* this value can be increased up to 2000 */
#define MAXTHROTTLE 1850
/* This is the speed of the serial interface. 115200 kbit/s is the best option for a USB connection.*/
#define SERIAL_COM_SPEED 115200
/* In order to save space, it's possibile to desactivate the LCD configuration functions */
/* comment this line only if you don't plan to used a LCD */
#define LCD_CONF
/* motors will not spin when the throttle command is in low position */
/* this is an alternative method to stop immediately the motors */
//#define MOTOR_STOP
/* some radios have not a neutral point centered on 1500. can be changed here */
#define MIDRC 1500
/* experimental */
/* camera trigger function : activated via AUX1 UP, servo output=A2*/
//#define CAMSERVO
#define CAM_SERVO_HIGH 2000 // the position of HIGH state servo
#define CAM_SERVO_LOW 1020 // the position of LOW state servo
#define CAM_TIME_HIGH 1000 // the duration of HIGH state servo expressed in ms
#define CAM_TIME_LOW 1000 // the duration of LOW state servo expressed in ms
//****** end of advanced users settings *************
Dilber MC Theme by HarzeM modified by Madcortina